NetworkSherpa

Post navigation

Welcome to STF
Linksys has made a newer version of logviewer. Client port numbers are dynamically assigned and can be reused once the session is closed. X X Automatic Program Updates. Save for later Add to Favorites. Port scanner tool can be used to identify available services running on a server, it uses raw IP packets to find out what ports are open on a server or what Operating System is running or to check if a server has firewall enabled etc. The logging mechanism added in V1.

navigating networks

Tutorial: Configure port fowarding in Load Balancer using the Azure portal

You can use the snake topology to test your backplane if you so wish. If you wanted to stress both line cards and the fabric you could use the following topology.

That topology would stress all 16 x M 10Gports at line rate whilst giving the backplane 80Gbps of traffic. Thanks again for the comment. I stand corrected; your detailed scenario is more stressful that what I had originally envisioned. The forwarding numbers measured by the two different tests come with some important distinctions. Thanks for the extra details. Just my two cents. Thanks for the comments!

Hello John, This is an interesting bit. Please can you advice if you were able to find any leads for the full mesh test? It would be nice to know more about it. I really need it…. The Loopback patch is a just a physical cable either fiber or copper, depending on the port-type of your switch.

From Spirent tester ports, reversed mac address traffic streams will be sent, mac addresses will get learnt on appropriate ports. Because, we are for sure not interseted in unknown unicast flooding throughput even there are only 2 ports in one VLAN. Upon receiving a frame from the testers input port, the switch would forward the frame directly to the return port, bypassing all the intermediate ports.

You would end up with a two-port test. The next vlan makes a similar decision, etc. Thanks for your comment. Hi John, Thanks for the quick response. So now on the port forwarding page of these types of routers you can set which WAN connection the rule is for. So you have to figure out which you need and that's simple: The problem with this is some times they will have your computer name listed multiple times, and each computer name points to a different IP.

So if you choose the wrong one the port forwarding rules won't work. In the Thomson you have to go to the device list and remove the extra entries. The 2wire doesn't give that option, rebooting the routers may help clear the extra entries.

So keep this in mind, I have seen this keep port forwarding from working since the computer name has a different IP than what your computer actually has. Lets say I have a Thomson router, I go to add a port forwarding rule and my computer name shows up 3 times in the device list. Which one do I choose? Well at that point you need to go to the device list and see what IP each one has.

Check what your local IP is and remove the extra ones that don't match. If you can't remove them just make sure to choose the one that points to your correct local IP.

Then your port forwarding will be fine at that point. If you choose the wrong one it will be pointing to a different local ip and so of course your port forwarding won't work. There are some routers such as Linksys, D-Link and many others that do not do any checks if a port is already in another port forwarding rule. So when there are multiples of the same port number the port forwarding rule will not work.

As you can see port is in 2 rules. The 1st one points to a different IP than that of the 2nd rule. So the router will honor the 1st rule and the 2nd port forwarding rule to port fails. By removing the 1st rule the 2nd one will now work. DMZ is a open all ports rule. And on most routers it over rides the port forwarding rules.

So if you have DMZ enabled and it isn't pointing to the machine you need the ports open on, then this will create problems. So if your setting up port forwarding rules, make sure DMZ is disabled. I have found there are also some simple things you can do as well to get things working. Here is one example: Some routers need to be rebooted after settings have been applied. Either by design or by a bug this some times helps.

My Netgear here at home normally doesn't have any trouble, but every now and then when I set up a new port forwarding rule it wont work till I reboot the router. So all you need to do is pull the power cord, wait a few sec.

Then plug it back in. Make sure to give it time to come back up before you test again. Turn ON windows firewall! Believe it or not, I have helped a few people where the port forwarding wouldn't work with the firewall off in windows. No other firewall was installed. So when I was scratching my heading trying to fig out what was going on I decided to turn the firewall back on, add the ports to the firewall to let them through and it worked!

So this is also another thing you can try. I still cant explain it myself. As per 2 if you use only the windows firewall try adding the ports your forwarding to it, not just the program that is going to use them. The simple port forwarding program makes this easy with one click on the tools menu. I have helped a few people where once the ports where added everything worked fine. If you haven't been able to tell, the windows firewall can be a bit strange on some systems! Yes I know this is a easy answer but let me explain.

There is some malware out there that installs a network driver that hijacks your connection, and every webpage you go to gets redirected to an advertisement. This shows that malware, viruses and other things can easily hijack the network and really screw things up. This is for you Verizon users out there. No port forwarding of any kind would work and every time we added a new rule the router complained the port was already in another rule Even though the user had no other rules set up.

Which is every port! Keep in mind that sometimes the router it self may be bad and even the Windows networking can be as well. Now these do happen, but they don't happen much. A firewall by nature blocks all incoming connections unless otherwise specified. Sometimes it becomes necessary to open these connections because of a game or other application. This process is called creating an open port or port forward.

We think that forwarding a port should be easy. That's why we created Network Utilities. Our software does everything that you need to forward a port. It is important to setup a static ip address in the device that you are forwarding a port to. This ensures that your ports will remain open even after your device reboots.

This second step is logging into your Netgear WGR router. This router uses a web interface, which means you need to login using a web browser. It shouldn't matter what web browser you use. After opening the web browser of your choice, locate the address bar. It should look like this:. The address bar is normally at the top of the page.

Remember a router's IP Address is sometimes called the computer's default gateway. Once you have finished entering the correct IP Address, simply press Enter on your keyboard. You should then see the following screen:.

Log in to Azure

Leave a Reply