TP-Link Network Router AC1750 user manual

TP-Link AC3150V2 Overview

TP-Link TL-WR541G - Wireless Router User Manual
Enter text from picture: Time There are nine submenus under the System Tools menu shown in Figure Fcc Statement Specifications are subject to change without notice. Other brands and product names are trademarks or registered trademarks of their respective holders. The default value is disabled. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

Manualslib has more than 192 TP-Link Wireless Router manuals

TP-Link AC3150V2 User Manual Wireless MU-MIMO Gigabit Router

However, there is no guarante. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Operation is subject to the following two conditions: This product can be used in the following countries: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives: Make sure that the package contains the above items.

If any of the listed items are damaged or missing, please contact your distributor. Name Status Indication Off Power is off. Flashing The Router is working properly. On The Router is connected to some wireless device s. WLAN Data is being tra. This button is used for both WPS and Reset function. There are two ways to. Connecting the Router 2. Connect the power adapter to the power socket on the Router, and the other end into an electrical outlet.

The Router will start to work automatically. The diameter of the screw, 3. Figure Router Status 4. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. The default type is Dynamic IP. If you get address and find error when you go to a Web site, it is likely that your DNS servers are set up improperly.

Connect Manually - You can configure the router to make it connect or disconnect manually. After a specified period of inactivity Max Idle Time , the router will disconnect from the Internet connection, and you will not be able to re-establish your connection automatically as soon as you attempt to access the Internet again. User Name - Enter the user name for Click Login to start Click Logout to end Host Name - This field is required to be filled by some service provider.

If you choose These fields are case-sensitive. Auth Server - Enter the authenticating server IP address or host name.

Auth Domain - Type in the domain suffix server name based on your location. To use this option, click the radio button.

If you want your Internet connection to remain active at all times, enter "0" in the Max Idle Time field. Otherwise, enter the number in minutes that you wish to have the Internet connecting last unless a new link is requested. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately. Connect on Demand - You can configure the router to disconnect from your Internet connection after a specified period of inactivity Max Idle Time.

If your Internet connection has been terminated due to inactivity, Connect on Demand enables the router to automatically re-establish your connection as soon as you attempt to access the Internet again. Internet connection to remain active at all times, enter 0 in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Internet connection terminates.

Sometimes the connection cannot be disconnected although you specify a time to Max Idle Time, since some applications are visiting the Internet continually in the background. Click the Save button to save your settings.

If you click the Save button, the router will prompt you to reboot. SSID to a different value. The default region is United States. When you select your local region from the pull-down list, click the Save button, then the Note Dialog appears. Limited by local law regulations, version for North America does not have region selection option. Channel - This field determines which operating frequency will be used. Enable Wireless Security — The wireless security function can be enabled or disabled.

If disabled, the wireless stations will be able to connect the router without encryption. Hexadecimal format stands for any combination of hexadecimal digits , a-f, A-F in the specified length.

Radius Password - Enter the password for the Radius Server. Be sure to click the Save button to save your settings on this page. The router will reboot automatically after you click Save. Privilege - Select the privileges for this entry. Description - A simple description of the wireless station. To set up an entry, follow these instructions: First, you must decide whether the unspecified wireless stations can access the router or not.

To add additional entries, repeat steps When bit, or bit, or bit is selected, WEP key will be enabled. To modify or delete an existing entry: Click the Modify in the entry you want to modify. If you want to delete the entry, click the Delete. Click the Save and the Return button. The filtering rules that configured should be similar to the following list: If you select the radio button Allow the stations not specified by any enabled entries in the list to access for Filtering Rules, the wireless station B will still not be able to access the router, however, other wireless stations that are not in the list will be able to access the router.

If the numbers of connected wireless stations go beyond one page, click the Next button to go to the next page and click the Previous button to return the previous page. This page will be refreshed automatically every 5 seconds. Address Lease Time - The Address Lease Time is the amount of time in which a network user will be allowed connection to the router with their current dynamic IP Address. You cannot change any of the values on this page. To update this page and to show the current attached devices, click on the Refresh button.

Click the Save button. Click the Enable All button to make all entries enabled Click the Disabled All button to make all entries disabled. Click the Delete All button to delete all entries Click the Next button to go to the next page and Click the Previous button to return the previous page. It is possible that you have a computer or server that has more than one type of available service.

If so, select another service, and enter the same IP Address for that computer or server. The router records this connection, opens the incoming port or ports associated with this entry in the Port Triggering table, and associates them with the local host. When necessary the external host will be able to connect to the local host using one of the ports defined in the Incoming Ports field.

You can select it, and the application will fill in the Trigger Port, incoming Ports Range boxes and select the Enable checkbox. It has the same effect as adding a new rule. After you set the DMZ host, the firewall related to the host will not work.

Figure Firewall Settings Enable Firewall - the general firewall switch is on or off. Enable Domain Filtering - set Domain Filtering is enabled or disabled. Keep the field open, which means all LAN ports have been put into the field. Domain Name - Type the domain or key word as desired in the field.

A blank in the domain field means all websites on the Internet. Status - Select Enabled or Disabled for this entry on the Status pull-down list. Click the Save button to save this entry.

Click the Enable All button to make all entries enabled. Click the Disabled All button to make all entries disabled. Select a value between 5 and 60 seconds in the pull-down list. The Packets Statistic interval value indicates the time section of the packets statistic. The default is disabled. If enabled, the ping packet from the Internet cannot access the router.

The default value is disabled. If enabled, the ping packet from the LAN port cannot access the router. Figure Static Routing To add static routing entries: Click the Add New button. Click the Delete All button to delete all entries. This function can guarantee the minimum bandwidth or limit the maximum bandwidth for the specified IP address or IP range to make full use of the supplied bandwidth. If you are not clear about that, please contact with your ISP for help.

Mode — There are 2 types of mode: Click any of them, and you will be able to scan or configure the corresponding function. Click the Add New Select the Bind checkbox. Click the Save button to save it.

Find the desired entry in the table. Click Modify or Delete as desired on the Modify column. To find an existing entry: Click the Find button shown in figure Configure - Load or delete item.

Type the domain names your dynamic DNS service provider gave. Domain Name - The domain names are displayed here. There are nine submenus under the System Tools menu shown in Figure To upgrade the router's firmware, follow these instructions: Click Browse to view the folders and select the downloaded file.

TP-Link AC3150V2 Specs

Leave a Reply